How long can a DAC cable be?
Passive up to about 5 m: IEEE specifies passive links up to 5 m for 100G and 7 m for 40G, and at 25G up to 3 m without and 5 m with RS-FEC. Active copper cables go to 7 or 10 m. Need more? Use an AOC or two transceivers with fiber.
You want a DAC because it's cheap and low-power, but the next rack is just a bit further away. How far can you go before the link throws errors? The limit sits in roughly the same place for every speed.
Maximum length per speed
| Speed | What the standard or datasheet says | Our range |
|---|---|---|
| 10G SFP+ | no IEEE length; in practice passive up to 5 m, active 7 and 10 m (Cisco) | 0.5 to 5 m |
| 25G SFP28 | IEEE 802.3by (25GBASE-CR): up to 3 m without RS-FEC, up to 5 m with RS-FEC | not in the shop |
| 40G QSFP+ | IEEE 802.3ba (40GBASE-CR4): up to 7 m; passive in practice often up to 5 m | 0.5 to 2 m |
| 100G QSFP28 | IEEE 802.3bj (100GBASE-CR4): up to 5 m | 0.5 to 5 m |
Within those lengths the link is specified by the standard. Longer passive cables exist, but come without that guarantee.
Longer than 5 m
- AOC — fiber with the optics fixed in the connector, thin and light. We have 10G AOCs from 1 to 10 m.
- Transceivers with a patch cord — for anything beyond that, or when the link goes through a patch panel. On multimode that's an SR optic at each end.
- Active copper cable — exists, but we don't stock it as standard. Ask if you need one.
At 25G the FEC setting also depends on cable length; see FEC explained. The choice between DAC, AOC and optics is in DAC, AOC or transceivers with fiber. Our DACs: SFP+ 10G and QSFP28 100G.
More questions on this
Why is a long DAC thicker?
The longer the cable, the more signal loss in the copper. Manufacturers therefore use thicker conductors: Cisco uses 30 AWG up to 3 m for 10G and 24 or 26 AWG at 4 and 5 m. A thicker cable is stiffer and has a larger bend radius.
Does a 25G DAC need FEC?
It depends on the length. Cisco specifies for 25G DACs: no FEC up to 2 m, BASE-R FEC at 2.5 to 3 m and RS-FEC at 4 to 5 m. Set the same FEC mode at both ends.
What is the difference between a passive and an active DAC?
A passive DAC is just copper with an EEPROM at each end and draws about 0.1 W. An active cable has a chip that boosts or rebuilds the signal, so it reaches further, but uses more power.
Passende Produkte und Dienstleistungen
Further reading
- DAC vs AOC vs optics: what to use in the rack and across the row
Passive DAC, active copper, AOC or transceivers with a patch cord? Reach, power, cost, cable bulk, breakout and coding compared, plus a checklist.
- Latency: why a DAC beats optics (and when it actually matters)
DAC, AOC or optics in the rack? Where latency in a short link really comes from, why a passive DAC wins, and when those nanoseconds are worth chasing.
- FEC explained: why your 25G or 100G link won't come up (and what RS-FEC costs)
Light levels fine, link still down or full of errors? It's often FEC. Which link needs which FEC, why a mismatch kills the link, and how to read the counters.