Optiken

Own router on KPN fiber: AON, GPON or XGS-PON, and which SFP

Remove the KPN box and plug the fiber straight into your own router? How to tell AON, GPON and XGS-PON apart, which SFP or ONT you need and what to configure.

5 Min. LesezeitVon Yvan Watchman

You want the KPN box out of your meter cupboard and the fiber straight into the SFP port of your UniFi, MikroTik, OPNsense box or FRITZ!Box. Whether that works, and with which module, depends on one thing: the technology KPN delivers at your address. Below you'll see how to tell whether you have AON, GPON or XGS-PON, what you need for each, which router settings KPN uses, and what to do step by step if you're on AON.

First: which technology do you have?

KPN delivers over its own networks (formerly Reggefiber) and Glaspoort, and the technology differs per address. Here's how to recognise it in the meter cupboard:

  • AON — an NT or media converter with a short fiber lead from the FTU and an Ethernet port to your modem, without a PON light. At KPN it often says Genexis.
  • GPON — a box with a PON light, or a label saying GPON or ONT.
  • XGS-PON — XGS-PON or 10G-PON on the label, or a 4 or 8 Gbit/s subscription. KPN only delivers those speeds on XGS-PON.

The installation date helps too. The rule of thumb on the KPN thread at Tweakers: everything KPN has installed since mid-2021 is XGS-PON; older lines may still be AON. If in doubt, ask KPN literally: "Which technology do you deliver at my address: AON, GPON or XGS-PON?"

A misconception we see a lot: "GPON and AON use the same wavelengths, so my BiDi module will work." It fits optically, yes: it transmits at 1310 nm and receives at 1490 nm, just like a GPON ONT. But a BiDi module doesn't speak GPON. The central office won't recognise it and you get no connection.

AON: one BiDi SFP and you're done

On AON you have your own fiber to the central office. KPN doesn't need to register anything. You need a 1000BASE-BX10-U module: transmit at 1310 nm, receive at 1490 nm.

  • Always the U variant — the D side is already in the central office. Two of the same side won't give you a link.
  • 20 km is fine — our GLC-BX-U20-SO has more reach than you need, but works on the short line to the central office too.
  • Coding — pick your router's brand, or MSA (Generic) if your router doesn't do a vendor check.
  • Check the colour of your FTU — blue is SC/UPC, green is SC/APC. Never plug a green connector into a blue port or the other way round; it damages the connector.

For a blue FTU, use our SC/UPC to LC/UPC patch cord. It's duplex; for BiDi you use one fiber: the SC of that fiber in the FTU, the LC of the same fiber in the module. A green FTU needs SC/APC to LC/UPC. That one isn't in the shop yet, but we supply it on request.

One caveat: KPN is gradually moving AON areas to XGS-PON, and upgrading to 4 or 8 Gbit/s moves you over anyway. Your BiDi module won't work there. Check before you switch.

GPON: no own ONT

On GPON, KPN doesn't allow your own ONT. If you want your own equipment, you can ask KPN to move you to XGS-PON free of charge. After that, the next section applies.

XGS-PON: your own ONT stick, with registration

Searching for "KPN XGS-PON own SFP module"? The answer is yes, but it isn't a regular optic. XGS-PON shares the fiber with other addresses via a splitter, transmits at 1270 nm and receives at 1577 nm. You need an XGS-PON ONT, often as an SFP+ stick, whose serial number you register in the KPN service tool. On the KPN Community, users report that the service tool doesn't always accept the serial number; mind the format (four letters plus eight hexadecimal characters).

We don't sell XGS-PON sticks. Such a stick has to match the network and KPN, and we can't guarantee per address that it works. Ask KPN or the forums which ONTs others have running.

Router settings

According to KPN's specifications for your own equipment on fiber:

  • Internet — PPPoE on VLAN 6.
  • IPTV — VLAN 4.

Settings can change. KPN's own documentation is leading, not this article.

Connecting it yourself on AON

  • Confirm in the meter cupboard or with KPN that your address has AON.
  • Order the BX-U module, not the D, with your router's coding or MSA (Generic).
  • Pick an SC-to-LC patch cord matching your FTU colour: blue (UPC) or green (APC).
  • Set PPPoE on VLAN 6 in your router, and VLAN 4 if you use IPTV.
  • Connect the patch cord to FTU and module, remove the KPN box and check the connection.

What to do now

Don't know your technology yet, or with a provider other than KPN? Our which SFP for my fiber tool lists it per provider, including what to ask. On AON, order the GLC-BX-U20-SO and a patch cord; on average you'll have them within a day. Green FTU or unsure about your line? Get in touch and we'll take a look with you.

Yvan Watchman

Über den Autor

Yvan Watchman

Gründer von FiberNxt und Xyphen IT

Yvan Watchman ist Gründer von FiberNxt und Xyphen IT. Er baut und betreibt seit Jahren Netzwerke und Rechenzentrumsinfrastruktur in und um Amsterdam.

LinkedIn-Profil

Passende Produkte und Dienstleistungen

Häufig gestellte Fragen

How do I know whether my KPN line is AON or GPON?

Look at the box between the FTU and your modem. An NT or media converter without a PON light (often made by Genexis) points to AON. A PON light or a label saying GPON or ONT means PON. A 4 or 8 Gbit/s subscription always runs on XGS-PON. If in doubt, ask KPN.

Can I use my own SFP module on KPN XGS-PON?

Only an XGS-PON ONT, often shaped as an SFP+ stick, and only after you register its serial number in the KPN service tool. A regular BiDi SFP doesn't work on XGS-PON. We don't sell XGS-PON sticks.

Does a BiDi SFP work on GPON?

No. GPON uses the same wavelengths as AON, so the module fits optically, but it doesn't speak the GPON protocol. You won't get a connection. KPN doesn't allow your own ONT on GPON either.

Weiterlesen