Ordering a cross-connect in Amsterdam: LOA, meet-me room and what goes wrong
Connecting your rack to a carrier, AMS-IX or cloud on-ramp? What a cross-connect is, what the LOA says, real lead times and how to test the link.
Your rack sits in an Amsterdam data center and it needs to reach a carrier, AMS-IX or a cloud on-ramp. That means a cross-connect. The real questions are what you order, who does which part, and why the port sometimes refuses to come up after the job is marked complete. This guide covers the order itself, what an LOA contains, which cabling and optics to have ready, realistic lead times, and a checklist for the first test.
What you are actually buying
A cross-connectCross-connect Physical link in a data centre between your rack and another party's, usually via the meet-me room and provided by the data centre itself. is a permanent physical cable between your equipment and another party's inside the same building. Equinix describes it in exactly those terms: a dedicated, physical cabling link between two parties. It normally runs through the meet-me roomMeet-me room Space in a data centre where carriers, exchanges and customers physically interconnect. Cross-connects between parties usually run via the patch panels in this room., the space where carriers and customers interconnect. The TIA-942 data center standard has a comparable space, the entrance room, for access-provider equipment and demarcation points.
The demarc is the patch panel where the cross-connect terminates. The last stretch, from that panel to your switch, is often a separate job. At Nikhef you request that patch separately and you are not allowed to run it yourself. Equinix offers a "Patch my equipment" option at additional Smart Hands fees.
The LOA: no paperwork, no cable
The party you are connecting to issues a Letter of Authorization. It tells the data center three things: you have permission, which port on which panel the cable should land on, and which media to use. AWS calls it an LOA-CFA, adding a Connecting Facility Assignment, and its authority lapses if the cross-connect is not completed within 90 days.
You then order from your own data center, through its portal:
- Equinix — in the Customer Portal you upload the LOA or select a Digital LOA, then pick your own panel and port. By default the portal takes the next available one.
- Digital Realty — for a ServiceFabric port you download the LOA first, then request the cross-connect in the Marketplace portal (Digital Realty and Megaport ports) or the Interxion Customer Portal (Interxion ports).
- Nikhef — fibre to Digital Realty AMS9 and AMS17 is managed by Digital Realty, fibre to Equinix AM3 by Equinix. The patch to your rack is a request to Nikhef.
Single-mode, duplex and the connector
Since 31 March 2024 Equinix only takes single-mode cross-connect orders; copper and multimode were discontinued. Connectors can be SC, ST, FC or LC. AMS-IX Amsterdam lists single-mode with LC/PC at 1310 nm for 10GE-LR, 100GE-LR1 and 400GE-LR4, but notes that the connector type depends on the site and the meet-me room. So read the connector off your LOA and bring a patch cord that fits it.
Duplex optics such as LR and LR4 need two fibres. A BiDiBiDi Bidirectional transceiver: transmits and receives over a single fiber on two different wavelengths (for example 1310/1550 nm). Always deployed in pairs with mirrored wavelengths. optic transmits and receives over one, which matters for cross-connects: London exchange LINX describes it as doubling the capacity of each cross-connect. Check whether your data center actually sells a simplex cross-connect, and always order BiDi as a U/D pair. The trade-offs are in BiDi vs duplex: which to choose.
Lead times and cost
Equinix states a provisioning SLA of 24 hours for up to three cross-connects and 36 hours for four to six, with per-site intervals that can differ. With AMS-IX, you receive the demarcation details after signing, use them to order the cross-connect, and the NOC then tests the connection with you. The exchange plans for about a week. We found no published lead time for Digital Realty in Amsterdam, so ask before you commit to a migration date.
On cost we keep it short. Equinix charges a one-time installation fee plus a monthly charge, and the amounts depend on your contract. Other operators have their own models. Equinix publishes no amounts, so we are not going to invent numbers.
Handed over: how to test the link
According to Megaport, the most common reason a port stays down after a cross-connect is swapped polarity. It is a quick fix, if you know where to look.
- Compare the completion notice with your LOA: panel, port and connector.
- Read the DOM values on your side: is there Tx power, and does Rx power come back?
- Swap Tx and Rx on one end if you receive no light, then measure again.
- Place a loopback at the demarc if in doubt, to see which side the fault is on.
- Ask the data center for a written Tx/Rx reading if it still does not work.
- Label the cable at both ends with the cross-connect ID from your order.
AMS-IX even publishes what it expects at its panel: for 10GE-LR, Tx between -8.0 and 0.5 dBm and Rx between -14.4 and -0.5 dBm. How to read those values is covered in DOM/DDM explained. Whether your optic makes the full path is a quick sum with the power budget.
Optics in your rack on time
The data center runs the cross-connect; the optics and patch cords are on you. FiberNxt delivers same day in the Amsterdam area, including Digital Realty sites. That covers the data centers in Science Park, Zuidoost and Schiphol-Rijk (including Equinix, Digital Realty, Nikhef and Maincubes). Pick your optics, for example 10G SFP+ or 100G QSFP28, plus an OS2 patch cord. Want someone to run the patch and measure the link? See our services.

Founder of FiberNxt and Xyphen IT
Yvan Watchman is the founder of FiberNxt and Xyphen IT. He has been building and running networks and data centre infrastructure in and around Amsterdam for years.
Related products and services
Frequently asked questions
Who provides the LOA for a cross-connect?
The party you are connecting to: the carrier, the internet exchange or the cloud provider. Their LOA grants permission and names the exact panel and port on their side. You take that LOA to your own data center and order the cross-connect there.
How quickly does Equinix deliver a cross-connect?
Equinix states a provisioning SLA of 24 hours for up to three cross-connects and 36 hours for four to six. Intervals can differ per data center. AMS-IX itself plans for roughly one week to get a new connection live.
My cross-connect is complete but the port stays down. Now what?
First check whether you see any Rx power. No light very often means Tx and Rx are crossed; have them swapped on one end. Then compare the completion notice with your LOA and, if needed, ask the data centre for a written optical reading.