What is the difference between SR, LR, ER and ZR?
It's the reach class of an optic: SR is multimode at 850 nm up to 300 m (OM3) or 400 m (OM4), LR is single-mode at 1310 nm up to 10 km, ER single-mode at 1550 nm up to 40 km and ZR single-mode at 1550 nm up to about 80 km.
The code after the dash (10GBASE-SR, -LR) tells you two things: which fiber the optic belongs on and how far it reaches. It says nothing about the shape; SR exists as SFP+, SFP28 and QSFP. Below are the 10G values; at 25G the multimode distances are shorter.
10G: the four classes side by side
| Code | Fiber | Wavelength | Reach (10G) |
|---|---|---|---|
| SR | multimode (OM3/OM4) | 850 nm | 300 m OM3, 400 m OM4 |
| LR | single-mode (OS2) | 1310 nm | 10 km |
| ER | single-mode (OS2) | 1550 nm | 40 km |
| ZR | single-mode (OS2) | 1550 nm | approx. 80 km |
SR, LR and ER are IEEE standards (802.3 clause 52). ZR is not: it's a convention between manufacturers, and Cisco itself notes it isn't part of the 10G standard. Besides these four we also carry a 20 km and a 100 km variant.
What about SX, LX, EX and ZX?
Those are the 1G names. SX is multimode at 850 nm (up to 550 m), LX single-mode at 1310 nm (up to 10 km with most vendors), EX 40 km and ZX 70 to 80 km. EX and ZX aren't IEEE names either, but they are widely used.
At 25G and 100G you see the same letters: 25GBASE-SR reaches 70 m on OM3 and 100 m on OM4, 25GBASE-LR 10 km. At 100G you also get DR (500 m) and a digit for the number of lanes, as in LR4.
How to choose
Fiber first: multimode means SR, single-mode means LR or longer. Then distance, with margin for connectors and splices; check it with a power budget. The full story, including the 1G variants, is in reach codes explained. The optics themselves are under 10G SFP+ and 1G SFP.
More questions on this
Is LR the same as LX?
No. LR is 10G (10GBASE-LR), LX is 1G (1000BASE-LX). Both use 1310 nm over single-mode, but an LX SFP won't do 10G and an LR SFP+ won't talk to a 1G optic.
Can I use an ER or ZR on a short link?
Only with an attenuator. A strong laser on a short fiber overloads the receiver at the far end. Cisco specifies 5 dB of attenuation for its 10G-ER below 20 km. Pick the smallest reach that covers your distance.
Does an SR optic work on single-mode?
SR is only specified for multimode. If single-mode is installed, pick LR or longer.
Related products and services
Further reading
- Optical power budget: will this optic make your link?
An 8 km link with four patch points: will an LR do, or is it marginal? How to work out power budget, link loss and margin, with three worked examples.
- Single-mode vs multimode: OS2, OM3 and OM4 compared
OS2 or OM4, OM3 or OM4? Distances per standard, what optics and fiber really cost, and when you're better off running single-mode everywhere.
- Reach codes decoded: SX, LX, SR, LR, ER, ZR
SFP LX vs SX and 10GBASE-SR vs LR: what each reach code means, which come from IEEE 802.3, which fiber and wavelength they need, and how to choose.